No products in the cart.
Twin Medical Gas Outlet with Flowmeter integrated and Diss
To quote the equipment, you must specify the following:
* Specify gas type (oxygen or medical air).
* Installation version (wall, architectural or ambulance).
*For a formal quote, download the equipment configuration sheet, click here and fill in the form, add it to your information providing valid data (name, full address, email, telephone, country, postal code).
Hi, I have a doubt about Twin Medical Gas Outlet with Flowmeter integrated and Diss
Description
Twin Medical gas Outlet, main outlet with integrated flow meter (Not removable) and secondary outlet with DISS CGA-V5 (Diameter Indexed Safety System) threaded plug. Manufactured in meeting NFPA99 code and ASTM B819 (Clean for oxygen use).
Primary Valve (Back Assembly):
- Brass made Primary valve 360°rotation, copper piping extention “K" type 10mm (internal diameter).
- Polypropylene injection ckeck valve.
- Thermoplastic injection TPVs FDA grade seals.
- Wall and Architectural (Patient Bedhead Units) Hardware Mounting Modular assembly, carbon steel sheet 18 gauge nickel finish made.
- Ceiling Hardware Mounting Modular assembly available, upon request.
- Stainless steel spiral locks.
- “Pin-Guide" No cross connection safety system die-cut corresponding to a specific medical gas type to Rough-in assembly insertion.
Secondary Valve (Rough-in Assembly):
- Stainless steel front plate made with brass feeding valve, it includes a plunger for connection and disconnection of secondary equipment, fastening to the primary valve is by millimeter screws.
- Two-branch body for connection with the permanent position flowmeter and the secondary DISS threaded outlet, the primary valve is fastened by millimeter screws.
- Thermoplastic injection TPVs FDA grade seals.
- Stainless steel spiral locks.
- ABS plastic injection trim wall plate chrome finish, same material to architectural equipments trim plate, chrome finish.
- “Pin-Guide" No cross connection safety system corresponding to a specific medical gas type to Back-assembly reception.
- zamak chrome finish trim wall plate option (upon request).
Medical Gas Outlet Flow:
- 240 L.P.M. gas flow (if diameters of the main medical gas piping allow it).
Load Capacity on the Secondary OUTLET (DISS):
- 450g Maximum load capacity.
Attention
- It should not be cleaned with “CHLORINE" or its derivatives, it could cause corrosion in stainless steel.
Specifications
Criteria for use
- The use of the double outlet with integrated secondary equipment will prevent the Hospital’s operation and maintenance personnel from worrying about the compatibility of the coupling of secondary oxygen and medical air dosing equipment about type of inlet or coupling in the wall outlets and architectural equipment therefore, all types of plugs or couplings of the oxygen and medical air outlets will be standardized and normalized to a single type of plug.
- Standard of the plug corresponds to a “threaded” coupling with greater safety and reliability and meeting the specifications of CGA-V5 (Compressed Gas Association) code for safety plugs of Non-Crossing Gases by Diameter DISS (Safety Indexed System by Diameter)
- It will prevent accidental loss of the air and oxygen flowmeters due to their constant connection and disconnection, as the “Non-removable” Flowmeters will be permanently attached to the oxygen and medical air outlet.
- Using the secondary DISS outlet will allow and additional flow to be supplied for other medical devices simultaneously, such as coupling other Flowmeters, hoses and regulating valves.
Legal Notice
Intellectual and industrial property: All rights reserved.- All access to this website is subject to the following conditions: The reproduction, permanent storage and dissemination of the contents or any other use that has a public or commercial purpose is forbidden without prior written notice and approval of Grupo Arigmed S. de R.L. de C.V.
- All documents, images and contents, on this website are from the Intellectual property of Grupo Arigmed S. de R.L. de C.V., any type of copy, plagiarism or similarity in those (documents, images and contents), will be object of legal actions to avoid its use by unauthorized persons, organizations or companies, as well to compensate author´s damage caused.
