Screw Connect DISS CGA-V5 Medical Gas Outlet USA
*To a quote contact our technical and commercial personnel; Customer information must be valid and true (name, full address, email, telephone, country, zip code, I.D. tax).
**We always request clear specifications to make a formal quote.
Description
Outlet-Inlet for medical gas distribution with threaded coupling type DISS CGA V5, thread-specific fixation for each gas.
- Compliance with NFPA 99, CGA V5, NBR 12188
- With U.L. (Under Writers Laboratories) certification
- Threaded coupling compatible with DISS CGA V5 technology.
- Compatible with U.S. and Brazilian brands.
- Do not use chlorine or its derivatives; may cause corrosion on metal parts.
- Do not use oil or its derivatives.
- Manufactured in Mexico, ARIGMED.
Specifications
⚙️ Technical Specifications
🔧 Medical Gas Outlet Connection
- Manufactured in stainless steel and aluminum.
- Threaded coupling inlet type DISS CGA V5.
- Thread-specific fixation for each gas and vacuum.
- Safety pin with position registry to prevent gas crossover (between primary and secondary valve).
- Complies with NFPA 99 and ASTM B819 (medical grade, clean for oxygen use).
- Compatible with all U.S. and Brazilian standards (NBR).
🛠️ Primary Valve
- Brass base with 360° rotation.
- Extension with copper tube type “K”, internal diameter: 10 mm.
- Automatic shut-off valve (check) in injected polypropylene.
- TPVs thermoplastic seals, FDA grade.
Available Versions:
-
- Wall mounting: modular bracket in carbon steel sheet, nickel finish, 18 gauge.
- Patient headwall mounting: same as above.
- Ceiling mounting: upon prior specification.
- Spiral locks in stainless steel.
- Mounting bracket with specific registry by gas type, for insertion of the secondary valve guide pin, compatible with U.S. brands.
🔩 Secondary Valve
- Flat front in stainless steel or aluminum.
- Inlet type DISS CGA V5.
- Secured to the primary valve with metric screws.
- Gas-coded inlet, compatible with DISS CGA V5 technology.
- Automatic shut-off valve (check) in high-resistance ABS.
- TPVs thermoplastic seals, FDA grade.
- Spiral locks in stainless steel.
- Includes guide pin to prevent gas crossover, compatible with U.S. and Brazilian brands.
🧱 Mounting Frames
- Wall frame: made of injected Zamak, chrome finish.
- Patient headwall frame: made of high-resistance injected ABS plastic.
💨 Available Gases
- Oxygen
- Medical Air
- Medical Vacuum
- Nitrous Oxide
- Waste Anesthetic Gas Disposal (WAGD)
- Carbon Dioxide
- Nitrogen
- Instrument Air
🎨 Color Identification
- According to NFPA 99
- According to ISO (specify standard if greater precision is required)
📈 Technical Parameters
| Parameter | Value / Condition |
|---|---|
| Gas outlet flow rate | 240 LPM (depending on supply diameter) |
| Extraction capacity | 90 LPM (depending on vacuum pipe diameter) |
| Secondary load capacity | Maximum: 450 g |
| Operating pressure | 50–55 PSI for all gases and 160–180 PSI only for nitrogen and instrument air |
| Maximum test pressure | 100 PSI for all gases and 160–180 PSI only for nitrogen and instrument air |
🔐 Safety and Compatibility
- Safety pin with registry to prevent gas crossover: Included
- Compatible with U.S. brand registries.
🛡️ Standards and Certifications
- Complies with: NFPA 99, ASTM B819, NBR 12188
- Quality system: ISO 13485, ISO 9001
- Safety certification: U.L (Under Writers Laboratories)
📘 Installation, Operation and Maintenance Manual
This document is protected and available exclusively for our brand’s equipment. To request it:- Access the form in the Manuals and After-Sales Service section.
- Send an email with the requested information.
- Complete the corresponding form.
Legal Notice
Intellectual and industrial property: All rights reserved.- All access to this website is subject to the following conditions: The reproduction, permanent storage and dissemination of the contents or any other use that has a public or commercial purpose is forbidden without prior written notice and approval of Grupo Arigmed S. de R.L. de C.V.
- All documents, images and contents, on this website are from the Intellectual property of Grupo Arigmed S. de R.L. de C.V., any type of copy, plagiarism or similarity in those (documents, images and contents), will be object of legal actions to avoid its use by unauthorized persons, organizations or companies, as well to compensate author´s damage caused.
